Turbine Flow Meters

Turbine meters are volumetric flow measurement devices that have high accuracies and are ideally suited to low viscosity fluids. Unlike most flow measurement techniques, turbine flowmeters can work well in extreme high pressure and extreme high and low temperature fluid flows. Turbine flow meters are able to measure hydrocarbons, chemicals, water, air, natural gas, industrial gases, and cryogenic liquids with some of the highest accuracies among all known flow measurement technology.

Turbine flow meters

Turbine meters are volumetric flow measuring meters. As liquid or gas passes through the turbine meter housing, it causes the freely suspended turbine blades to rotate. The velocity of the turbine rotor is directly proportional to the velocity of the fluid passing through the flow meter.

Turbine flow meters measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels and other liquid types with lower viscosity and for applications requiring high accuracies of 0.5% or better to ensure precise flow measurement measurements.
Smart Measurement ALTM turbine flow meters have been used successfully in a wide variety of applications and industries that require Turbine flow measurement technologies.

Turbine Flowmeter

Key Applications

Water & Energy flowmeters from SmartMeasurement have been successfully installed in a wide variety of industries and applications including:

Why choose a Turbine flow meter

When it comes to simple mechanical flow meters, turbine meters offer the best accuracy as well as excellent turn-down ratios. With its simple design, the turbine flowmeter offers a low-cost solution for many clean liquid and gas applications. No other mechanical-type flow meter can match its advantages. Turbine meters are also successful in very high-pressure and height-temperature applications where other flowmeters would be limited.

Smart Measurement’s ALTM Turbine Flowmeters are available in a wide range of materials enabling it to be used in many corrosive applications. Moreover, with its low mass rotors, it offers excellent response time as well as the ability to work effectively in pulsating flow applications.

Special Cases

A typical turbine meter calibration curve illustrates the relationship between fluid flow and the K-factor (pulses/gallon). Turbine meters can be highly accurate; between ±0.5-1% with some as high as ±0.1% of reading (actual flow) and linearity of ±0.25% over a 10:1 range or ±0.15% linearity over a 6:1 range. The repeatability is typically from ±0.2% to ±0.02% over the linear range.

After they are calibrated, all turbine flowmeters are provided to the end user with a K-factor indicated in pulses per unit volume within the manufacturer’s rated accuracy band. For better accuracy, several K-factors may be provided for different portions of the meter’s flow range. More importantly, the K-factor applies only to the fluid for which the meter was calibrated. 

Smart Measurement’s ALTM turbine flow meters come in sizes ranging from ½” to 12” (15-300 mm) and feature a wide turn-down ratio with minimum uncertainty and a very repeatable output. The ALTM is excellent for precise measurement of instantaneous flows of low-viscosity fluids such as tap and demineralized water, fuels, liquefied gases, light fuel oils, solvents, and pharmaceutical fluids.

Please visit our industrial measurement applications section to find more detailed information about where our Turbine flow meters have been successfully used.

Request a quote for Turbine flow meters for your application, or contact Smart Measurement to learn more.

Altmt Flowmeter

ALTMT STANDARD

Altm Sanitary Flowmeter

ALTM SANITARY

Altm Lft

ALTMLF

Advantages of using Turbine Flow Meters

Turbine meters may be installed vertically or horizontally. When installed vertically, the fluid flow must be moving upward through the meter. If installed horizontally meters must be installed in a level, horizontal position with both registers and dial face facing upward. It is recommended to install it horizontally to avoid falling debris. Turbine meters must operate in a completely full line of fluid at all times. The downstream pipe should be arranged to provide sufficient back pressure to maintain a full line of water. Turbine meters come with various types of pickoffs, sensors, and transistors.

Reluctance Pickoffs

A reluctance-type pickoff module consists of a permanent magnet, a ferrous metal pole piece and a wire coil. Each time a turbine blade passes through the field created by the magnet, the coil generates a pulse. Each pulse represents a discrete volume of the fluid; the number of pulses per unit volume is referred to as the meter’s K-factor. 

Inductance pickoffs also come with a permanent magnet embedded in the rotor, as each blade passes the coil, it generates a voltage pulse representing one complete revolution of the rotor. The outputs of both pickoff styles are continuous sine waves with the frequency being proportional to the maximum flow rates. Since the pulse signal at low flow rates is very weak, the distance between the pickoff and associated display electronics or preamplifier must be short. 

Capacitive Sensors

Capacitive sensors produce a sine wave by generating an RF signal that is amplitude-modulated by the movement of the rotor blades.

Hall-Effect Transistors

Hall-effect transistors change their state when they are in the presence of a very low strength (on the order of 25 gauss) magnetic field.  Very small magnets are embedded in the tips of the rotor blades. In this type of system, the rotors are typically made of a non-magnetic material, like polypropylene, Ryton, or PVDF (Kynar). Their signal output is a square wave pulse train, at a frequency proportional to the volumetric flow rate.

Having no magnetic drag, the Hall Effect can operate at lower flow velocities (0.2 ft/sec) than magnetic pickoff designs (0.5-1.0 ft/sec). The Hall-effect sensor also provides a signal of high amplitude (typically a 10.8-V square wave), permitting transmission distances of up to 3,000 feet between the sensor and the electronics without amplification.

Theories of Operation

Installation Methods

Primary Application

Special Features

Main Markets

Installation Methods

Primary Application

Special Features

Main Markets

Installation Methods

Primary Application

Special Features

Main Markets

Installation Methods

Primary Application

Special Features

Main Markets